CAM Position Sensor
- 1996.5-2003 Powerstroke 7.3 Turbo Diesel.
- F7TZ-12K073-B.
- Keep an extra in your truck, they fail without warning.
- Free Shipping (Lower 48 States)!
|
$25.00
$8.00
$20.00
$20.00
|
 |
|
|
Improved Cam Position Sensor (CPS) for 7.3L Ford Powerstroke
- If you own a 7.3L Powerstroke, you may already be aware of the shortcomings of the stock Cam Position Sensor (CPS). It is common for the CPS to fail causing the engine to run poorly or to stop running altogether and it usually happens at the most inconvenient times, such as in traffic or pulling a load so many owners carry a spare CPS.
- This International Harvester CPS can be installed in the Powerstroke engine and will make the engine run quieter, smoother while increasing performance and mileage!
- Provides a different signal (changes timing from standard CPS) to the Ford computer which results in a more accurate injection of fuel and better running engine with easier starts!
- Works on all 99-03 7.3L Powerstroke Diesel.
- 94-97 models may require shimming to install correctly.
- Results vary by applications!
- Free Shipping (Lower 48 States)!
|
$129.00
$8.00
$20.00
$20.00
|
|
|
|
Ford exhaust back pressure sensor (EBP) 7.3 Power Stroke DI Turbo Diesel 1997-2003
- FORD Retail: $146.99
- Fits all 94-03 7.3 Power Stroke DI Turbo Diesel.
- This is an OEM replacement part new from Ford Motor Company.
- This one replaces the old part numbers of F7TZ-9J460-AA, BA and 3C3Z-9J460-AA.
- Free Shipping (Lower 48 States)!
|
$119.99
$20.00
|
|
|
|
Exhaust Backpressure Sensor Replacement Tube
Replace when your tube connected to the sensor is full of dry soot, or rusted.
Built for exact fit.
Free Shipping (Lower 48 States)!
|
$69.99
|
|
|
|
Injection Control Pressure sensor (ICP) 7.3 Power Stroke DI Turbo Diesel 1997-2003
- Fits all 97-03 7.3L Power Stroke Direct Injection Turbo Diesel.
- This is an OEM replacement part new from Ford Motor Company.
- This one replaces the old part numbers of F6TZ-9F838-A.
- Free Shipping (Lower 48 States)!
|
$149.99
$20.00
|
|
|
|
Ford Water in Fuel Sensor 7.3 Power Stroke DI Turbo Diesel 1994-1997
- Fits all 94-97 7.3 Power Stroke DI Turbo Diesel.
- This is an OEM replacement new part.
- Free Shipping (Lower 48 States)!
|
$39.00
$20.00
|
|
|
|
Exhaust Backpressure Sensor Eliminator
- OBDII codes are detected and logged during a diagnostics scan of specific sensors by the PCM at start, when the Exhaust Pressure Control Valve (EPCV) is showing High/Low pressure.
- Eliminates P0478 Code.
- Easy to install.
- This can be due to tube connected to the sensor being full of dry soot, or due to bad sensor.
- Built for exact fit.
- Free Shipping (Lower 48 States)!
|
$39.00
|
|
|
|
Exhaust Backpressure Sensor Eliminator Stage II
- OBDII codes are detected and logged during a diagnostics scan of specific sensors by the PCM at start, when the Exhaust Pressure Control Valve (EPCV) is showing High/Low pressure.
- Eliminates P047X Codes related to Exhaust Back Pressure!
- Easy to install.
- This can be due to tube connected to the sensor being full of dry soot, or due to bad sensor.
- Built for exact fit.
- Free Shipping (Lower 48 States)!
|
$69.00
|
|
|
|
MAP Sensor Maxmimizer
- Allows the MAP sensor to send a maximum boost available signal to the PCM.
- Eliminates the Service Engine Soon (SES) light from coming on when high turbo boost is attained.
- Maximizes power and throttle response.
- Fits all 7.3L trucks, 1999+ with waste gate.
- Compliments the 18K Power module.
- Compliments any Chip or programmer that over boosts, so NO MORE OVERBOOSTING SES LIGHT!
- Works with stock or modified truck.
- Not intended for MPG increase.
- Complete plug and play.
- Free Shipping (Lower 48 States)!
|
$39.00
|
|
|
|
Exhaust Backpressure Valve Terminator
- Did you gut your Exhaust Pressure Valve?
- Upgraded your Turbo Pedestal?
- Easy to install.
- DO not leave your factory plug hanging with open circuit.
- Built for exact fit.
- Free Shipping (Lower 48 States)!
|
$39.00
$29.00
|
|
|
|
Air Heater Plug Code Eliminator
- Code P0541 is detected and logged during a diagnostics scan of specific sensors by the PCM at start, when the Air Intake Heater plug is disconnected.
- The harness, used in conjunction with the AIH plug will stop the PCM from throwing the dreaded P0541 code "Intake Air Heater Relay 1 Low ".
- Easy to install.
- Use it when you remove the AIH.
- Built for exact fit.
- Free Shipping (Lower 48 States)!
|
$19.00
|
|
|
|
|
|
|
If you see it cheaper elsewhere, call us and we'll try to meet or beat the price!
